Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
American Standard Kitchen Remodeling: The Orlando Owner’s Guide
If your American Standard kitchen fixtures or fittings have failed, a full kitchen remodel in Orlando typically runs $14,000 – $45,000 installed, with smaller galley kitchens starting around $9,000. We carry and install American Standard-compatible faucets, sinks, and plumbing trim, and we can match most parts to your existing model or upgrade you to current-production equivalents. Most Orlando homeowners call us after a fixture has leaked one too many times, a sink rim has corroded, or a faucet cartridge has simply worn out after years of Orlando’s hard water doing its quiet work.
Here’s what we see most often: a homeowner notices a drip that won’t stop, then finds mineral crust building around the base of the spout, then discovers the shutoff valve under the sink has seized. By the time we arrive, the question isn’t usually “can you fix this faucet” – it’s “should I fix this faucet, or is it time to redo the whole kitchen?” That’s the conversation we’re built for.
Which American Standard Models This Applies To
American Standard has produced kitchen lines under a few distinct families over the decades: the Colony and Heritage series from the 1990s and 2000s, the current Studio and Pekoe lines, and the commercial-grade Selectronic touchless models. The compatibility gotcha we run into in Orlando: older American Standard kitchen faucets used a 1/2-inch IPS threaded shank, while newer models moved to a 3/8-inch compression fitting. If you’re swapping a faucet rather than rebuilding it, the supply line connection underneath is where most DIY mismatches happen.
Here’s the decision we walk every homeowner through. On a faucet, an OEM American Standard cartridge is usually $25 – $50 and worth it – aftermarket ceramic disc cartridges for American Standard bodies are widely available, but we’ve seen enough seat tolerances that don’t quite match to steer clear on anything we warranty. On a sink, there’s no real OEM-versus-aftermarket debate: American Standard sinks are fireclay, cast iron, or stainless, and the replacement is the replacement. Sink strainer baskets, mounting clips, and rim seals we keep as universal-fit quality parts on the truck.
To identify your model, look under the sink for a small metal or foil tag on the faucet body, or check the inside of the cabinet door. If the tag is gone, pull a cartridge and measure the diameter – most American Standard kitchen cartridges are either 35mm or 40mm. We can match it from that measurement alone in most cases.
Styles & brands we work with
Signs Your American Standard Kitchen Remodeling Is Failing
- Water pressure drops to a trickle at the spray head. Nine times out of ten this is a clogged aerator or diverter, but in Orlando’s hard water we also see scale buildup inside the spray hose itself. The fix is usually a $5 aerator or a $30 hose replacement, not a new faucet.
- The handle turns but doesn’t fully shut off. That’s a worn cartridge seat. American Standard ceramic discs last a long time, but once sediment scores the disc, no amount of handle-tightening will stop the drip. A $40 cartridge beats a $400 faucet every time.
- Water pools around the base of the spout after every use. This means the O-ring seals under the spout have flattened or cracked. On American Standard models from the Heritage era, these O-rings are a known wear item in humid climates – Orlando’s year-round moisture accelerates the breakdown.
- The sink rim shows rust staining where the sink meets the counter. That’s water wicking under a failed rim seal. If it’s been going on long enough, the countertop substrate under the sink lip starts to swell, and what started as a $15 seal job becomes a countertop repair.
- You hear a rattle or vibration when water runs at certain temperatures. Loose internal components or a failing pressure-balance cartridge. On some American Standard Selectronic models, the solenoid valve chatters when it’s on the way out – and once the solenoid goes, the faucet stops working entirely.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Orlando homeowners, a focused American Standard fixture replacement – faucet, sink, or both – lands between $400 and $2,500 installed, depending on whether we’re swapping a cartridge or tearing out a corroded sink and rebuilding the counter cutout. A full kitchen remodel built around American Standard plumbing runs $14,000 – $45,000. Small kitchens fall at $9,000 – $20,000; mid-size kitchens with new cabinetry, counters, and plumbing trim sit solidly in the $25,000 – $35,000 range around Orlando.
Every quote we write in Orlando includes the part, the labor, the disposal of the old fixture, and the workmanship warranty. You get a written price before we start – never a verbal estimate that grows on the final bill. If you’re unsure whether to repair or replace, call us and we’ll tell you straight which way the numbers lean.
| Service | Typical Orlando Installed Range |
|---|---|
| Faucet cartridge replacement | $150 – $350 |
| Faucet replacement (labor included) | $400 – $1,200 |
| Sink replacement | $600 – $1,800 |
| Small kitchen remodel | $9,000 – $20,000 |
| Full kitchen remodel | $14,000 – $45,000 |
DIY or Call Us?
You can safely replace an aerator, swap a spray head, or tighten a loose handle on your own – those are five-minute jobs that don’t touch the shutoff or the supply lines. Where I’ve seen DIY go sideways in Orlando kitchens is underneath: old angle stops that snap when you try to close them, braided supply lines that burst when untwisted, and cartridge removals that strip the retaining nut and lock the old part into the faucet body permanently.
If your fixture involves anything below the counter line – shutoff valves, supply lines, drain connections – or if the sink itself is coming out, call us at (850) 920-7745. Tell me what the problem is. We’ll figure out the rest from there.
FAQs
In Orlando’s water, an American Standard kitchen faucet with a ceramic disc cartridge typically lasts 10 – 15 years before the cartridge needs replacement, and 20+ years before the faucet body itself fails. Hard water shortens that window – we replace cartridges on 8-year-old faucets regularly in neighborhoods like Winter Park and Conway that draw from harder groundwater sources.
Yes, if the faucet body is sound and the failure is in the cartridge, O-rings, or spray head. Those repairs run $150 – $350 in Orlando. If the body shows pitting, cracks, or corrosion at the base, replacement is the honest call – patching a corroded faucet just moves the leak downstream. Call (850) 920-7745 and we’ll tell you which one you’re looking at.
A straightforward faucet replacement is a two-hour job. A sink replacement with sink cutout matching and rim sealing takes half a day. A full American Standard kitchen remodel in Orlando runs 4 – 8 weeks depending on cabinetry lead times and countertop fabrication. We’ll give you the timeline in writing before we start.
We stock common American Standard ceramic disc cartridges, O-ring kits, spray heads, and diverter assemblies on our vans, so most faucet repairs in Orlando happen same-visit. For less common Heritage-era or Selectronic parts, we source through American Standard distribution channels, usually to your door in two to three business days. We work with the same specification-grade partners across cabinetry and surfaces too – KraftMaid and Wellborn for cabinets, Cambria and Silestone for counters.
If you’ve got an American Standard fixture that’s been giving you trouble, or you’re ready to talk through a full Orlando kitchen remodel built around quality plumbing that lasts, call (850) 920-7745 for a free estimate. We’ll give you a written price, a named crew you’ll recognize at the door, and a full year to make sure it’s right.
Written by Isaac Pruett, Owner, Mason Remodeling Co Orlando at Mason Remodeling Co Orlando, serving Orlando and nearby areas.
