Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Bathroom Remodeling: The Orlando Owner’s Guide
If you own a Boral bathroom and something’s gone wrong, here’s the short version: Mason Remodeling Co Orlando stocks Boral-compatible shower bases, wall panels, trim, and sealants, and we install them throughout Orlando for a total project cost that typically lands between $9,000 and $28,000 depending on scope. Most Boral failures we see are leaks at seams or cracked panels, not catastrophic structural issues, which means the fix is usually faster and cheaper than a full tear-out. You’ll know it’s time to call when you spot water staining on the ceiling below, soft spots at the shower base, or sealant that’s pulling away from the panels.
Before we dig deeper, one honest note: Mason Remodeling Co Orlando is an independent service provider, not a Boral factory outlet or affiliated dealer. We handle Boral products every week because they’re common in Orlando homes built after 2010, and we know their quirks better than most. Tell me what the problem is. We’ll figure out the rest from there.
Which Boral Models This Applies To
Boral’s bathroom line in the U.S. market centers on their solid-surface and cultured-marble shower systems and tub surrounds. The main product families you’ll find in Orlando homes are the Boral ShowerBase series (sized from 30×60 up to 36×60 inches), the Boral WallPanel system (typically 1/4-inch or 3/8-inch thick panels with a tongue-and-groove edge), and their coordinated trim kits that finish outside corners and edges. If you’re not sure which one you have, look for a small embossed label on the back of the shower base or on the underside of a shelf. It’ll show a model number starting with “BS” (for shower bases) or “WP” (for wall panels), followed by the dimensions in inches.
The compatibility gotcha most Orlando owners hit is this: Boral changed their panel thickness specification around 2018. Pre-2018 panels are a true 3/8 inch. Post-2018 panels measure closer to 1/4 inch at the tongue. If you splice a new panel into an older shower without accounting for that difference, the seam will never sit flush and the sealant line will fail within months. We measure every existing panel with calipers before ordering replacements. It’s a 30-second check that saves a redo.
On OEM versus aftermarket: Boral OEM panels and bases are still available for most models, but lead times run 2 to 4 weeks from their distribution centers. Quality aftermarket equivalents from suppliers we’ve vetted (same substrate, same color match, same edge profile) are often in our Orlando shop within 3 to 5 business days. We’ll tell you which is which and let you choose, because you should know what’s going into your shower and what it costs.
Styles & brands we work with
Signs Your Boral Bathroom Remodeling Is Failing
- Sealant pulling away from the seams. Boral panels expand and contract with Florida’s humidity cycles. Over 5 to 8 years, the flexible sealant at the panel joints dries out and loses grip. That’s the #1 cause of hidden water damage we find in Orlando bathrooms.
- Soft spots in the shower base. The Boral base sits on a mortar bed. If the original installer skimped on the mortar (common in tract-built Orlando homes), the base flexes underfoot. Flex equals micro-cracks. Micro-cracks become leaks.
- Discoloration or staining at the bottom 6 inches of the wall panels. Water wicking up behind the panel from a failed seam will eventually show through as a tea-colored stain. By the time you see it, the backer board behind it is already breaking down.
- A musty smell that lingers after cleaning. Not always a leak. Sometimes it’s organic matter trapped behind the trim. But if you’ve cleaned the visible surfaces and the smell stays, we treat it as a leak until proven otherwise.
- Cracks radiating from the drain opening. Hairline cracks around the drain are a structural issue with the base itself, usually from the original rough-in being slightly off-center. It never seals correctly after that, and the only durable fix is base replacement.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what Boral bathroom remodeling actually costs in Orlando, with real numbers:
- Full Boral shower replacement (base, panels, trim, fixture reset): $9,000 to $18,000 depending on size, access, and whether the backer board behind the panels needs replacement.
- Complete Boral bathroom remodel (shower, flooring, vanity, fixtures, drywall, paint): $18,000 to $28,000, driven by material choices and whether we’re moving any plumbing.
- Seam repair and re-seal only: $400 to $900. This is a stopgap, not a fix, if the panels are already compromised behind the seams.
The range depends on what we find when the old panels come off. If the studs and backer board are dry and solid, you’re at the low end. If we’re replacing rotted framing and mold-damaged drywall, you’re at the high end. We don’t surprise you with those numbers after the fact. Mason Remodeling Co Orlando gives you a written price before any work starts, and that price holds unless you approve a change in writing. No verbal estimates that drift. No invoices that grow on their own.
Every Boral replacement we install in Orlando is covered by our 365-Day Done Right Promise. If the work is not right within one year of completion, we make it right at no cost to you. That’s the whole promise. 365 days from the completion date, stated plainly, no fine-print gymnastics.
DIY or Call Us?
You can safely check a few things yourself: run your hand along every seam and feel for gaps or crumbling sealant. Press gently on the shower base and feel for flex. Look at the ceiling below the shower for water stains. These checks tell you there’s a problem, not what the problem is.
What you should not do is attempt a panel removal on your own. Boral panels are heavy (a 36×60 wall panel runs 45 to 60 pounds), and they’re under tension when properly seated. A panel letting go mid-removal will crack, and it can take a chunk of drywall or a person’s foot with it. And the sealant behind Boral panels in Florida is often holding back more water than anyone expects. Pulling a panel “just to look” can release water into wall cavities and turn a $400 repair into a $4,000 one.
If the seam is failing or the base is flexing, call us at (850) 920-7745. We’ll assess it properly and give you a written price before we touch anything.
FAQs
In Orlando’s humidity, a properly installed Boral shower system lasts 15 to 20 years before panels need replacement. A poorly installed one shows problems within 5 to 8 years, almost always at the seams or the base. Call (850) 920-7745 if yours is in the second camp, and we’ll give you an honest read.
Yes, if the damage is limited to seam sealant and the panels themselves are sound. No, if panels are cracked, the base is flexing, or the backer board is wet. We’ll tell you which one you have before we quote anything, and estimates are free.
Most Boral panel replacements in Orlando take 2 to 3 working days from demo to final silicone cure. Full shower replacements run 4 to 6 days. We’ll give you the schedule in writing before work starts.
We stock the most common Boral trim profiles, sealants, and drain assemblies in our Orlando shop. Full panels and bases are ordered per project, with OEM lead times of 2 to 4 weeks and faster aftermarket options in 3 to 5 business days. We use the same spec-grade suppliers we trust for KraftMaid, Cambria, and Silestone jobs.
Have a Boral bathroom in Orlando that’s showing its age? Call (850) 920-7745 for a free estimate. A live person answers, and we’ll walk through what you’re seeing before we ever step foot in your home.
Written by Isaac Pruett, Owner, Mason Remodeling Co Orlando at Mason Remodeling Co Orlando, serving Orlando and nearby areas.
