Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Fence Installation: The Orlando Owner’s Guide
Boral fence installation in Orlando typically runs $3,500 to $9,000 installed depending on fence height, linear footage, gate count, and whether we’re replacing an entire run or matching into an existing Boral section. Most owners don’t realize something’s wrong until a panel starts leaning after a storm or a post shifts in sandy soil. The good news: Boral is one of the few fence materials we work with that rarely fails because of rot or termites. The bad news: when an Orlando thunderstorm pushes a weakened post over, you’re usually looking at a section rebuild, not a ten-minute fix. Call us at (850) 920-7745 and we’ll tell you straight what needs replacing and what can be saved.
Here’s what we see most often in neighborhoods like Dr. Phillips, Winter Park, and Baldwin Park. A homeowner has a Boral fence that’s been in the ground for six or seven years, looks fine from the street, but has one post that’s developed a slight lean. They ignore it until a summer squall rolls through, and then that lean becomes a collapsed section taking the adjacent panels with it. By that point, the fix is no longer a $200 post reset. It’s a full section replacement at $1,500 to $3,000 depending on how many panels and how much of the surrounding structure got stressed. We’d rather catch it early and do the smaller job.
Key Takeaways:
- Full Boral fence installation in Orlando: $3,500 – $9,000 depending on footage and gates
- Section replacement after storm or post failure: usually $1,200 – $3,500
- Boral doesn’t rot or attract termites, but Florida rain and sandy soil punish posts and hardware
- We write the price before any work starts, and that price doesn’t change
Which Boral Models This Applies To
Boral makes two main fence lines you’ll find around Orlando: their solid-panel privacy fence and their spaced-picket design. Both use the same basic post-and-panel construction, but the panel dimensions vary. Boral privacy panels are typically 4×8 feet or 6×8 feet, while picket sections come in 6-foot and 8-foot widths. Before you call us, check the inside face of a panel near a post – Boral stamps their name and sometimes a manufacturing code there. That code tells us the batch and helps us match color if we’re blending new panels into existing runs.
Here’s the compatibility gotcha most people don’t know: Boral panels are heavier than vinyl or wood by a meaningful margin. A 6×8 Boral privacy panel runs around 80 to 90 pounds. That’s not a problem when the fence was installed right, but we’ve seen plenty of Orlando fences that weren’t. Undersized posts, shallow post holes, or concrete footings that don’t extend below the root zone in sandy soil all fail prematurely under Boral’s weight. When we replace a Boral section, we don’t just match the panel. We check whether the existing posts can actually carry the load before we bolt anything on. OEM Boral parts are the right call when you’re matching an existing fence within a few years of installation. For older fences where Boral has discontinued a color or texture, we’ll recommend a high-quality aftermarket panel that matches the surrounding sections close enough that you won’t notice from ten feet away.
Styles & brands we work with
Signs Your Boral Fence Installation Is Failing
Most fence problems in Orlando show up before the actual failure. Here’s what to look for:
- Post lean, especially on the south or west side of the property. This is almost always a footing issue. Sandy soil plus shallow concrete equals a post that’s slowly tipping. In Baldwin Park and College Park, we see this constantly with fences installed by builders who skimped on post depth.
- Panels separating from posts at the bracket. Boral panels are heavy, and the brackets take all that weight every time the wind gusts. Once a bracket starts to pull, the panel shifts, and eventually one good storm finishes the job.
- Visible gaps between the bottom of panels and the ground, uneven from one section to the next. That means the posts are settling at different rates. It’s a warning sign that the fence is being stressed unevenly.
- Color fading or chalky residue on the surface. Boral holds up well to Orlando sun, but after five or six years of direct UV exposure, the surface can start to chalk. This doesn’t affect structural integrity, but it’s a sign the material is aging and may be more brittle if you’re planning to move or modify sections.
- Gate sagging or dragging on the latch side. A Boral gate is the heaviest moving part on the fence. If the gate post wasn’t set deep and wide, the whole assembly starts to lean inward, and the gate stops closing cleanly. That’s a repair we can usually do in one visit if we catch it before the gate post itself fails.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a full Boral fence installation in Orlando, plan on $3,500 to $9,000. The spread comes down to three things: linear footage, panel height, and how many gates you need. A small backyard enclosure with one gate at 4-foot height lands near the bottom. A larger property with 6-foot privacy panels and two gates lands near the top.
On partial replacements – which is what most Orlando homeowners actually need – you’re looking at $1,200 to $3,500 for a failed section or post repair. That includes removing the damaged panels and posts, setting new posts in concrete at the proper depth for Florida soil (usually 2.5 to 3 feet below finished grade), remounting the salvaged panels where possible, and matching new panels where the old ones can’t be saved. Labor is roughly 60% of the total; Boral materials make up the rest. You’ll get a written line-item price before we start, and that number doesn’t move on you at the end of the job. We cover our Boral work with the same guarantee we put on every project: if something’s not right within 365 days of completion, we fix it at no cost to you.
DIY or Call Us?
Boral fence work is not dangerous the way garage-door springs or electrical panels are, but it’s backbreaking and precision-dependent. If you want to reset a leaning post, that’s a job a capable homeowner can do with a post-hole digger, a level, and a full Saturday. But here’s where DIY goes wrong: most homeowners dig a hole, drop the post in, pour a bag of fast-set concrete, and call it done. The post is still connected to a 200-pound panel, and the footing is too shallow for Orlando’s sandy soil. Six months later, it’s leaning again. We also see homeowners reuse old brackets and rotted post caps because they didn’t realize the old hardware was part of the original failure. If the post is cracked, the bracket is pulling, or the gate side is involved, call us. Isaac Pruett will tell you the same thing he’s told homeowners all over Orlando: “Tell me what the problem is. We’ll figure out the rest from there.”
FAQs
A properly installed Boral fence with deep-set posts should last 15 to 20 years in the Orlando climate. That’s longer than wood but shorter than the 30-year ratings you’ll see on Boral’s marketing material, because Florida’s intense UV and storm cycles put real stress on the posts and hardware even when the panels themselves hold up. Most fences we replace in Orlando didn’t fail because of the Boral material. They failed because the original installation cut corners on post depth or bracket quality. Call (850) 920-7745 and we’ll tell you whether your fence can be repaired or needs to be replaced.
Yes, if the post itself is intact and the lean is from settling, we can often straighten and re-set it in one visit. If the post is cracked or the footing has completely broken free, it usually needs to come out. A straight post that’s simply sunk a few inches into sandy soil is a candidate for re-leveling; a post that’s visibly cracked at the base is not. Either way, we’ll inspect it and give you a written price before touching a tool.
Most section replacements are done the same day we start, typically four to six hours from removal to final cleanup. If we’re replacing multiple posts and the concrete needs to cure before we hang panels, that stretches to two days. You’ll know the timeline before we start, and it’s in the written price.
We keep a range of Boral-compatible brackets, post caps, and hardware on the truck for common repair scenarios, along with panels from our suppliers in the Orlando area. For exact-match Boral panels in a specific color or texture, we may need to order to match your existing fence. We’ll tell you if that’s the case before any work is scheduled, and the price is locked in writing before we begin. While we’re at it, we also work with KraftMaid, Cambria, and Silestone products on other projects, so we know the difference between OEM and equivalent-grade parts and we’ll give you an honest recommendation either way.
If your Boral fence is leaning, separating, or just doesn’t look right after a storm, call us at (850) 920-7745. We’ll walk the fence with you, put the fix in writing, and give you a straight answer on what it costs. Free estimates, written prices, and a crew you’ll recognize by name and photo before they ever ring the bell.
Written by Isaac Pruett, Owner, Mason Remodeling Co Orlando at Mason Remodeling Co Orlando, serving Orlando and nearby areas.
