Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mr-Glass Fence Installation: The Orlando Owner’s Guide
Mr-Glass fence installation in Orlando typically runs $3,500 to $9,000 for a complete perimeter job, depending on linear footage, the specific Mr-Glass panel series you own, and site prep. We stock Mr-Glass-compatible panels, posts, and hardware on our trucks, so a single-section repair or partial replacement can often be quoted the same day we come out. Most Orlando owners discover a problem after a storm blows a panel loose, or when a gate starts dragging and the hinge post shows rust at the base.
We’re an independent Orlando contractor, not a Mr-Glass factory outlet, which means you get a straight answer about whether your existing posts can be reused or need to be pulled and re-set in fresh concrete.
Which Mr-Glass Models This Applies To
Mr-Glass fence systems in Orlando fall into a few recognizable lines: the slim-profile extruded aluminum panels, the heavier-gauge privacy screens, and the older picket-style inserts that predate the current modular locking rail. The compatibility gotcha we see most often is rail width. The current Mr-Glass panels lock into a 2-inch top and bottom rail, but some Orlando homes built between 2008 and 2014 have the older 1¾-inch rail. You cannot seat a new panel into an old rail without an adapter, and forcing it bends the locking tab. If you’re not sure, measure the inside channel of your rail with a tape measure before you buy anything.
On the OEM-versus-aftermarket question: Mr-Glass factory panels are powder-coated to a specific spec that stands up to Florida UV. Aftermarket equivalents cost less, but the cheaper ones fade unevenly within three to five years in direct Orlando sun. We install both, and we’ll tell you which one makes sense based on where the panel sits and how long you plan to stay in the house. If we’re matching an existing fence, we use the factory panel, period. A mismatched powder coat shows up immediately and it’s the first thing you’ll notice every time you pull into the driveway.
Styles & brands we work with
Signs Your Mr-Glass Fence Installation Is Failing
- Panel wobble at the mid-rail. The locking tab has worn or been bent by wind load. The panel won’t fall out today, but it will rattle and eventually pop loose in a storm.
- Gate drag on the latch side. This usually means the hinge post has started to lean because the concrete footing wasn’t deep enough or has cracked. Re-hanging the gate is a waste of time until the post is fixed.
- White chalky residue on panels. That’s oxidation under the powder coat. It means the coating has failed. You can slow it but not stop it, and it spreads to adjacent sections.
- Corner post leaning outward. Tension from the rail pulls the corner post out of plumb over time, especially in sandy Orlando soil. A leaning corner eventually pulls every connected panel with it.
- Water pooling at post bases after rain. Standing water accelerates the corrosion on the post screws and the bottom rail. If your posts sit in low spots, we may recommend re-setting them with better drainage, not just swapping the visible parts.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full Mr-Glass fence installation in Orlando runs $3,500 to $9,000, and here’s what moves the number. Linear footage is the big one: a 100-foot run is toward the bottom of that range, a 250-foot wrap with two gates toward the top. Existing post condition matters more than most homeowners expect. Reusing straight, solid posts saves $400 to $900 versus pulling and re-setting them. Gate hardware, concrete work, and panel style each add or subtract from the total.
- Single panel replacement: $180 – $450 installed
- Gate re-hang with new hinges and latch: $250 – $600
- Post re-set (one post, new concrete): $300 – $550
- Full perimeter installation (100 – 250 linear feet): $3,500 – $9,000
Every quote includes the written price before we start, the parts and labor broken out separately, and the 365-Day Done Right Promise on the workmanship. If the panel shifts or the gate sags within a year of the completion date, we come back and fix it. No charge, no dispute process, no conditions. That’s not a sales line. It’s just how we operate, and Isaac Pruett will tell you the same thing on the phone.
DIY or Call Us?
Replacing a single Mr-Glass panel is something a careful homeowner can do in an afternoon, provided the posts are solid and the rail channels match. You’ll need a rubber mallet, a level, and someone to hold the panel while you seat the locking tab. What you shouldn’t do yourself is pull a post or re-set one in concrete. If that post is out of plumb and you set it wrong, every panel you hang after it inherits the error, and you’ll be looking at a wavy fence line until the day you call us anyway.
The other thing we’d flag: Mr-Glass panels are light enough that wind grabs them. If a panel comes loose near a walkway or driveway during a storm, don’t leave it half-hung. Call us at (850) 920-7745 and explain what you’re seeing. Tell me what the problem is. We’ll figure out the rest from there.
FAQs
A well-installed Mr-Glass fence lasts 15 to 25 years in the Orlando climate, with the powder coat typically failing before the structure does. Panels facing full southern exposure fade and oxidize fastest. If your fence is pushing 12 to 15 years and the coating is chalky, budget for replacement sooner rather than waiting for a panel to fail. Call (850) 920-7745 and we’ll give you an honest read on the remaining life.
Dented panels can sometimes be straightened if the damage is limited to the flat face, but cracked rails, broken locking tabs, and failed powder coat are not repairable. The coating matters because a bare aluminum patch will corrode differently than the rest of the panel. For anything beyond a minor dent, replacement is cheaper in the long run. An estimate is free, so you’ll know the number before you decide.
A single panel swap takes under an hour on site. A full fence installation in Orlando typically runs two to four days, depending on the number of posts being set and whether we’re pulling the old fence. Concrete needs a day to cure before we tension the rails, so that’s built into the schedule. We’ll give you a written timeline with the written price, and we stick to it.
We keep Mr-Glass-compatible panels, posts, gate hinges, and latches on our trucks for the most common Orlando installations. If we don’t have your exact panel series on board, we’ll source it and schedule the install within a week in nearly every case. We also carry parts for other lines we service, including KraftMaid, Cambria, and Silestone, so if another project is waiting, mention it during the visit.
No. The written price you approve is the price you pay, unless you ask us to add scope during the job. If we find a rotted post or a broken footing that wasn’t visible at the quote, we’ll stop, show you what we found, and give you a new written number before we touch it. You approve the change before any additional work happens. Call (850) 920-7745 for a free estimate.
Written by Isaac Pruett, Owner, Mason Remodeling Co Orlando at Mason Remodeling Co Orlando, serving Orlando and nearby areas.
