Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Kitchen Remodeling: The Orlando Owner’s Guide
Barrette kitchen remodeling in Orlando typically runs $14,000 to $45,000 installed, depending on cabinet layout, countertop material, and whether plumbing or electrical moves are involved. Most Barrette cabinet lines use standard 32mm European hinge boring and 3/4-inch box construction, so replacement parts and hardware are generally available same-week rather than special-order. What usually brings an owner to this page is a specific failure: a drawer glide that gave out, a soft-close hinge that snapped, a door that’s sagging, or a corner cabinet mechanism that no longer closes right. You notice it first as a small annoyance, then as a daily frustration.
Mason Remodeling Co Orlando is an independent service provider. We’re not affiliated with Barrette, but we work with their cabinet boxes, hinge systems, and hardware every week, because Barrette cabinetry shows up in a lot of Orlando kitchens, from College Park remodels to newer builds in Lake Nona.
Which Barrette Models This Applies To
Barrette’s kitchen lines fall into three general groups: stock, semi-custom, and a builder-grade series often installed in tract housing. The easiest way to identify what you have is to open a cabinet door and look at the hinge cup. Barrette stock lines typically use a 35mm cup hinge with a 6mm overlay, while their builder-grade boxes sometimes run a 26mm cup with a 1/2-inch overlay. That 9-millimeter difference is the single most common reason a homeowner buys the wrong replacement hinge online and has to return it.
For drawer glides, measure the drawer box depth and check whether the slide mounts to the side or underneath. Barrette’s semi-custom lines generally use full-extension undermount glides rated at 75 to 100 pounds, while stock lines carry side-mount epoxy-coated slides rated closer to 50 pounds. If a glide says “Barrette” on the body, it’s their OEM part and sizing is stamped on the bottom. Quality aftermarket equivalents from Blum or Hettich work in most Barrette boxes, but the mounting hole pattern doesn’t always line up, which means drilling new pilot holes. That’s a job you want measured twice.
In Orlando’s humidity, we also see more door warping on Barrette doors than on some competing brands. That’s not dog-whistle criticism, it’s just what’s true: MDF core doors with thermofoil faces will hold up fine in conditioned spaces, but if the kitchen sits over a garage that’s unconditioned or near a lanai door that gets opened constantly, the moisture swing can cause face delamination within five to seven years.
Styles & brands we work with
Signs Your Barrette Kitchen Remodeling Is Failing
- The drawer doesn’t close the last two inches. That’s almost always a broken soft-close catch or a glide that lost its ball bearings. The soft-close mechanism is a small piston inside the slide, and once it fails, the drawer still functions but slams shut.
- A cabinet door hangs lower on one side. Hinge screws into MDF boxes loosen over time, especially on doors opened dozens of times a day like the one under the sink or the door to the trash pull-out. Retightening works once or twice. After that, you need a repair plate or a new hinge.
- Corner cabinet mechanism grinds or binds. The lazy Susan or blind-corner swing-out runs on a steel post or bearing ring. In a Florida kitchen, dust mixed with cooking grease works into that ring and it gets stiff. Sometimes it just needs cleaning and graphite. Other times the bearing is done.
- Thermofoil face is peeling at the edges. That’s moisture intrusion, and once peeling starts it doesn’t stop. The fix is a replacement door or door front, not glue. We match the panel profile and finish from the Barrette door line or fabricate a matching front through our cabinet suppliers.
- Cabinet box sides are bowing. This happens under granite or quartz overhangs when the corner gusset or wall cleat wasn’t set right. It’s the least common failure but the most important to catch, because the countertop is load-bearing on the box.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
On the parts end, individual Barrette-compatible hinges run $6 to $30 installed, drawer glides $25 to $80 per pair installed, and replacement door fronts $120 to $400 depending on size and finish. A full kitchen remodel with Barrette cabinetry lands at $14,000 to $45,000 in Orlando, with cabinet installation alone at $4,000 to $13,000. Countertop installation runs $2,000 to $6,500, and backsplash installation adds $800 to $2,500.
What drives the spread is mostly countertop material and cabinet line: stock boxes with laminate counters sit at the low end, semi-custom with quartz and a tile backsplash at the high end. Every Mason Remodeling Co Orlando job starts with a written price before any work begins. You’ll see the parts, labor, and materials on the line items. No verbal estimate that grows on the final bill. The work is backed by our written guarantee for 365 days from the completion date, and if a repair or installation fails, we come back at no charge.
DIY or Call Us?
You can safely check a few things before calling: open a hinge and look at the cup size stamped inside, measure your drawer box depth, and note whether the glide mounts on the side or underneath. Swapping a hinge or adjusting a door is within reach for a patient homeowner with a Phillips driver and a level. But drilling pilot holes into MDF in the wrong place weakens the box, and over-tightening a repair plate can blow out the particleboard core. If the countertop is stone and the box is bowing, stop right there. That needs a professional’s eyes.
Most Barrette cabinet part issues we handle in a single visit. Call (850) 920-7745 and tell us what the problem is. We’ll figure out the rest from there.
FAQs
In an air-conditioned Orlando home, Barrette cabinets typically last 15 to 20 years before doors, glides, and boxes need meaningful attention. In kitchens with heavy humidity swings, like those opening onto a lanai or sitting over an unconditioned garage, thermofoil doors can start failing in 5 to 7 years. Call (850) 920-7745 for an honest assessment of your cabinets.
Yes, a soft-close hinge with a broken spring can sometimes be repaired by replacing the spring cartridge, but most modern Barrette hinges are sealed units, and replacing the hinge is cheaper than the labor to rebuild it. We’ll tell you which is true for your part when we look at it.
In most Orlando homes, a hinge, glide, or door adjustment is a 30 to 90 minute job per cabinet. A full door-front replacement takes longer because we match the finish and profile the same week. Call (850) 920-7745 to schedule a visit.
We carry common 35mm soft-close hinges, 50 and 75 pound undermount glides, repair plates, and bumpers on our service trucks. Unusual sizes or specific door profiles are ordered to match. The other lines we stock parts for include KraftMaid, Cambria, and Silestone.
No. The written price you get before work begins is the price you pay. We don’t issue change orders unless you add scope. Estimates are free, so call (850) 920-7745 for an exact quote.
Written by Isaac Pruett, Owner, Mason Remodeling Co Orlando at Mason Remodeling Co Orlando, serving Orlando and nearby areas.
