Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Delta Kitchen Remodeling: The Orlando Owner’s Guide
If you have a Delta kitchen fixture or component that’s failed and you’re weighing whether to repair or replace it as part of a larger Orlando kitchen remodel, here’s the straight answer: a full kitchen remodel in Orlando typically runs $14,000 – $45,000, and if the Delta part is the trigger for the project, we can usually get your job scheduled within two weeks and completed in four to eight weeks depending on scope. Most Orlando homeowners discover the problem the same way: a Delta faucet starts dripping at the base, a pull-down spray head loses pressure, or a cabinet hinge from a Delta-era install gives out and the door starts sagging. The good news is that a failed Delta part rarely means a failed kitchen. It usually means it’s time to decide between a targeted fix and a larger remodel you’ve probably been thinking about anyway.
Mason Remodeling Co Orlando is an independent service provider. We are not affiliated with Delta Faucet Company, but we work with Delta products every week across Orlando kitchens.
Which Delta Models This Applies To
Delta has been making kitchen faucets and fixtures for decades, and Orlando homes run the full range: 1990s single-handle models, mid-2000s pull-out sprayers, and the newer touch and voice-activated lines. The part that fails determines what we need to know. For faucets, the model number is usually stamped on a tag under the sink or printed on the side of the spout near the base. If that tag is gone, we measure the cartridge: most Delta kitchen faucets use a diamond-embedded ceramic disc cartridge, and the older ones take a ball-and-spring cartridge that’s a little harder to find these days.
Here’s the compatibility gotcha most homeowners don’t know: Delta’s RP series parts are not interchangeable across generations. A cartridge from a 2010 Leland faucet will not fit a 2018 Trinsic, even though both are “Delta kitchen faucets.” The mounting hardware changed, the cartridge dimensions changed, and the finish codes shifted. If you buy the wrong one online, you’ll find out after you’ve already taken the faucet apart. We keep the common cartridges on hand and verify the match before anything gets disassembled.
For the OEM-versus-aftermarket question: genuine Delta parts are manufactured to the exact tolerances of your original fixture, and in Florida’s hard water, that matters. Aftermarket cartridges can work, but we’ve seen too many with softer seals that degrade faster in Orlando’s mineral-heavy municipal water. For faucets, we recommend OEM. For cabinet hardware and hinges, quality aftermarket equivalents from Blum or Salice are often just as good and sometimes better than what Delta-era installers used originally.
We also stock parts and hardware for KraftMaid cabinetry, Cambria and Silestone countertop lines if your Delta kitchen includes those and you’re ready to refresh more than just the fixture.
Styles & brands we work with
Signs Your Delta Kitchen Remodeling Is Failing
Here’s what we see most often in Orlando kitchens, and what each symptom actually means:
- Faucet drips from the spout after you turn it off. The ceramic disc cartridge has a worn seal or a tiny crack. This is the single most common Delta failure, and in Orlando’s hard water it happens faster because mineral scale abrades the rubber seats over time. A new cartridge usually fixes it.
- Pull-down spray head loses pressure or won’t retract fully. The diverter inside the spray head is clogged with mineral deposits, or the weight on the hose has slipped. Sometimes the hose itself is kinked inside the cabinet because the original install left too little slack.
- Water leaks from the base of the faucet only when the water is running. The O-rings on the faucet body have dried out. In Central Florida’s heat and humidity cycle, rubber components age unevenly, and this is a common result.
- Cabinet door hinge sags and the door won’t close square. This is a hinge failure, not a wood failure. The original hinges have worn pivots. It’s a $15 part, but if every hinge in the kitchen is original and they’re all failing at once, that’s a sign the entire cabinet box installation from the original builder was low-grade.
- Delta touch faucet turns on by itself or won’t respond. The solenoid valve under the sink is failing, or the battery pack has corroded. Florida humidity is rough on electronics under the sink, and we’ve replaced enough of these to know the fix is usually simple but the diagnosis is not.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what you can expect to pay in the Orlando market for a Delta-related kitchen project:
| Scope | Typical Installed Price |
|---|---|
| Delta faucet cartridge or part replacement (targeted repair) | $175 – $450 |
| Full kitchen remodel with cabinets, counters, faucet/fixtures | $14,000 – $45,000 |
| Countertop replacement only (includes sink cutout and Delta faucet reinstall) | $2,000 – $6,500 |
| Cabinet installation only (includes all hinges, pulls, adjustment) | $4,000 – $13,000 |
| Kitchen island install or reconfiguration | $3,000 – $10,000 |
The range is wide because a College Park bungalow kitchen remodel looks very different from a Windermere custom job. What drives the price: the condition of existing plumbing and electrical, whether you’re keeping the cabinet layout or moving walls, the countertop material you choose, and whether the Delta fixture is being repaired or replaced outright.
Every quote we give includes the parts, the labor, and the haul-off. You get a written price before we start, and that price does not change unless you change the scope. The workmanship warranty runs 365 days from the completion date. If something isn’t right within that year, we come back and make it right at no charge.
DIY or Call Us?
There are two Delta repairs an Orlando homeowner can safely handle without much risk: swapping a pull-down spray head (it unscrews by hand or with a single wrench) and replacing a cabinet hinge (two screws). If you’re comfortable with those, go ahead. But here’s where DIY goes sideways: anything involving the faucet cartridge, the supply lines, or the solenoid on a touch faucet. Those sit under live water pressure, and a wrong move means a flooded cabinet, a warped floor, and a bigger bill than the original repair. We’ve seen it. We’ve cleaned up after it.
If the failure is part of a larger issue, or you’re not sure what you’re looking at, call us at (850) 920-7745. Tell me what the problem is. We’ll figure out the rest from there.
FAQs
In Orlando’s hard water, a Delta kitchen faucet cartridge typically lasts 5 to 8 years before it needs replacing, and the faucet body itself can go 15 to 20 years if the finish is cared for. Mineral scale is the biggest factor. If you notice dripping early, it’s usually a $200-$400 fix rather than a full replacement. Call (850) 920-7745 and we’ll tell you which one you’re looking at.
Yes, in most cases we can replace just the cartridge or the seals for $175 – $450 including parts and labor, which beats a $300 – $900 new faucet installation. If the faucet body itself is cracked or the finish is failing, replacement is the honest call. We’ll give you that answer straight before any work starts.
A targeted Delta part replacement (cartridge, spray head, hinge) takes 1 to 2 hours on site. A full kitchen remodel in Orlando runs 4 to 8 weeks depending on cabinetry lead times, countertop fabrication, and whether you’re changing walls or plumbing. We schedule in writing and hold to it. Call (850) 920-7745 for a project timeline based on your scope.
We keep the most common Delta cartridges, spray heads, O-ring kits, and cabinet hinge replacements stocked on our service trucks, so most targeted fixes are finished in one visit. For less common Delta series parts or finish-matched components, we source from our Orlando supplier network, and that typically adds 2 to 4 business days. Either way, the price is written before we order anything.
Written by Isaac Pruett, Owner, Mason Remodeling Co Orlando at Mason Remodeling Co Orlando, serving Orlando and nearby areas.
