Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Dvele Kitchen Remodeling: The Orlando Owner’s Guide
Dvele kitchens in Orlando typically run $14,000 – $45,000 when we remodel them, depending on cabinet layout, surfaces, and how much of the original Dvele system we’re keeping versus replacing. Most Dvele owners come to us with a specific failing part: a delaminating cabinet face, a warped drawer glide, a hinge that’s stripped out of the cabinet box, or a countertop seam that’s opened up in Florida humidity. We figure out what failed, match the replacement to your Dvele specs, and install it so the whole kitchen works like it should again.
Here’s what we see most often in Orlando: Dvele builds with a modular, panelized approach, which is great for consistency and precision, but Florida’s humidity cycle tests every seam, every laminate edge, and every factory-installed hinge. The kitchen parts that fail first are usually the ones exposed to moisture and daily wear: the sink base cabinet, the drawer fronts under the cooktop, and the edge banding on lower cabinet doors. If you’re noticing swelling, peeling, or doors that don’t close square, you’re probably looking at a parts-level fix, not a gut job.
Key takeaways:
- Installed Dvele kitchen remodeling in Orlando: $14,000 – $45,000, with parts-only repairs often far less
- We match Dvele’s European hardware specs and cabinet dimensions before ordering anything
- Written price before any work starts, every time, no exceptions
- 365-Day Done Right Promise on the full project
Which Dvele Models This Applies To
Dvele doesn’t sell through traditional retail channels, so identifying your exact kitchen configuration takes a little detective work, but we know where to look. The cabinet boxes, drawer glides, and hinge plates usually carry small manufacturer markings: look for a printed label inside the sink base cabinet or on the underside of a drawer box. That label typically shows the cabinet line, the finish code, and sometimes the production date. If the label’s gone or faded, we measure the door overlay, the drawer depth, and the hinge cup diameter to match what’s on your kitchen. Dvele kitchens we work on in Orlando span several of their series, from earlier Santa Cruz builds to newer Serra and Dvele IQ configurations, and the hardware spec matters. A 110-degree Blum hinge is not the same as a 170-degree opening, and swapping the wrong one changes how the door sits against the cabinet face.
The OEM question is real. Dvele’s factory components are good, but some original parts, particularly laminate edge banding and drawer glide dampers, are impossible to source individually now. We stock quality aftermarket equivalents that meet or exceed the original spec: Blum and Grass glides, Salice hinges, and matching laminate edge banding in the common Dvele finishes. If you want us to use OEM parts only, we can source them, but we’ll be honest with you when a quality aftermarket part is the better value. Mason Remodeling Co Orlando is an independent service provider, not affiliated with Dvele, and we tell every homeowner that before the first tool comes out.
Styles & brands we work with
Signs Your Dvele Kitchen Remodeling Is Failing
- Cabinet doors that won’t close square or rub against the frame. This almost always traces back to a worn hinge or a hinge plate that’s pulled loose from the cabinet box. In Orlando’s humidity, the cabinet box can swell just enough that the original hinge screws lose their bite.
- Drawer fronts that sag or scrape when you pull them. The clip-on glide system Dvele uses is sturdy, but after thousands of cycles the runner wheels develop flat spots and the drawer starts to ride rough. Replacing the glide pair is usually all it takes.
- Peeling or bubbling edge banding on lower cabinet doors. This is the classic Florida failure: moisture wicks into the banding adhesive, it loses grip, and the edge lifts. The dishwasher and sink base are almost always the first to go.
- Countertop seams that open up or darken. Dvele uses solid surface and quartz in most lineups, but a seam that wasn’t perfectly cured, or that sits in direct Orlando sun near a window, can separate. Left alone, water gets under the seam and damages the substrate.
- Soft-close mechanisms that slam. The damper inside the hinge or glide is a wear item. When it loses its hydraulic fluid, the door doesn’t slow down anymore. These are quick, inexpensive swaps when you catch them early.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a full Dvele kitchen remodel in Orlando, plan on $14,000 – $45,000 installed. At the lower end, you’re updating surfaces and replacing failing hardware while keeping the existing cabinet boxes. At the upper end, we’re gutting to the studs, reworking the layout, and replacing everything with spec-grade materials. For parts-level work, here’s what Orlando homeowners typically see:
- Single cabinet door replacement with matched finish: $180 – $450
- Drawer glide pair replacement (European system): $120 – $300 per drawer
- Edge banding repair on one door: $75 – $200
- Hinge replacement, all cabinets in a standard kitchen: $400 – $1,200
- Countertop seam repair: $250 – $800
- Soft-close damper replacement throughout: $300 – $900
Every price includes the part, the labor, and a written guarantee. We hand you a written price before any work starts, and that price doesn’t grow on the final bill. The guarantee runs 365 days from the completion date: if anything we installed or repaired fails, we come back and make it right at no cost to you.
DIY or Call Us?
Some things you can safely check yourself: whether a hinge screw just needs retightening, whether a drawer glide has a loose mounting tab, whether a soft-close damper popped out of its clip. But here’s where DIY goes wrong on Dvele kitchens: the cabinet boxes are dense and famously difficult to drill cleanly once the original screw holes strip. A homeowner with a cordless drill can turn a loose hinge into a blown-out cabinet box in about three seconds. Then we’re patching and re-drilling instead of doing a ten-minute parts swap. If the part is structural, if you’re not sure about the spec, or if the finish has to match perfectly, call us. Tell me what the problem is. We’ll figure out the rest from there. Reach us at (850) 920-7745 and we’ll walk you through it on the phone before scheduling anything.
FAQs
Dvele cabinet boxes are built to last 20 to 30 years with normal use, but in Orlando’s humidity, the finish and hardware typically need attention at the 10 to 15-year mark. Edge banding, hinges, and soft-close dampers are the first things to go. The cabinet boxes themselves usually stay structurally sound unless they’ve been repeatedly exposed to water from a dishwasher leak or sink overflow. Call (850) 920-7745 if you want us to inspect your kitchen and tell you honestly what’s left in it.
Yes, and we usually do. A delaminating door, a stripped hinge, or a worn glide is a parts problem, not a kitchen problem. We replace the failed component, match the finish to your Dvele spec, and the cabinet is back in service. We only recommend replacement when the cabinet box itself is water-damaged or swollen beyond what the hardware can tolerate. Call (850) 920-7745 for an exact assessment, and estimates are free.
Most single-part repairs take one to two hours once we have the correct component in hand. Full hardware swaps across a whole kitchen usually run half a day to a full day. If we don’t have the exact part on the truck, we order it, and we’ll tell you the lead time before you commit to anything. Call (850) 920-7745 and we’ll give you a straight answer on timing.
We keep common European hinges, glide sets, soft-close dampers, and matched laminate edge banding on our trucks because those are the parts Orlando Dvele owners need most. If your kitchen has an unusual finish or a less common hardware spec, we source it and schedule the install once it arrives. We also stock parts for KraftMaid, Cambria, and Silestone kitchens, so if you’ve got mixed brands in your home, we can handle it in one visit. Call (850) 920-7745 to check stock for your specific part.
Written by Isaac Pruett, Owner, Mason Remodeling Co Orlando at Mason Remodeling Co Orlando, serving Orlando and nearby areas.
