Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
IKO Kitchen Remodeling: The Orlando Owner’s Guide
IKO kitchen remodeling in Orlando typically costs $14,000 to $45,000 for a complete renovation, with the most common mid-range projects landing between $18,000 and $28,000. If your IKO cabinetry, countertops, or hardware is failing, we stock commonly needed replacement parts and can usually get less-common components within five to seven business days. Most Orlando homeowners discover the problem the same way: a drawer that no longer closes flush, a cabinet door hinge that sags and scrapes, or a countertop seam that pulls apart after a few humid Florida summers. The good news is that a failing part rarely means you need to gut the whole kitchen. We match the part, quote the fix in writing, and handle the install cleanly.
Key takeaways:
- Complete IKO kitchen remodels in Orlando run $14,000 – $45,000; part-specific repairs are usually far less.
- We verify compatibility with your IKO model before ordering anything, so you don’t pay for a part that doesn’t fit.
- Every replacement comes with a written price before work starts and our 365-Day Done Right Promise.
Which IKO Models This Applies To
IKO is primarily known in Orlando for its roofing products, but the brand also supplies kitchen remodel materials including laminate countertops, backsplash profiles, and cabinet-adjacent trim used in residential builds and rental property renovations. The compatibility question that trips up most Orlando homeowners is this: IKO kitchen products are not line-numbered the way KraftMaid cabinets are. If you have a KraftMaid cabinet box, you need a KraftMaid-series hinge, not a generic one that looks close. The same applies to Silestone and Cambria countertops: each manufacturer cuts sink openings and seam profiles to their own tolerances, and a “universal” replacement edge piece rarely sits right.
Here’s how to identify what part you actually need before anyone orders it. Check inside the cabinet door or drawer box for a printed label, usually on the hinge-side stile or the bottom of the drawer. If the label is gone, measure the hinge cup diameter in millimeters (typical IKO-compatible hinges are 35mm), the door overlay distance, and the bore pattern. For countertop seam or trim failures, measure the total length and the profile height at the exposed edge. When we order OEM, the part matches the original. When a quality aftermarket equivalent makes more sense, we tell you before we quote it, and we only specify equivalents that meet or exceed the original’s gauge and finish. We’re an independent contractor and not affiliated with IKO; we work with their products because Orlando homes have them, and we know how they fail here.
Styles & brands we work with
Signs Your IKO Kitchen Remodeling Is Failing
- Cabinet doors that sag or scrape the frame. The hinge plate has loosened, or the hinge arm is bent from years of the door being pulled past its stop. Hairline stress cracks around the hinge screws mean the cabinet box itself is starting to fail, not just the hardware.
- Drawers that stick or drop on one side. The slide has worn its ball bearings, or the nylon roller has flattened. In Orlando’s humidity, swollen MDF drawer boxes accelerate this; the slide is fine, but the drawer bottom has expanded and is dragging.
- Countertop seams that separate or discolor. Laminate seams lift when moisture gets into the particleboard substrate. You’ll see a dark line at the seam first, then physical separation. On Cambria or Silestone surfaces, seam failures usually signal original installation error, not product defect.
- Soft-close dampers that stop dampening. The piston inside the damper has failed, usually after 5 to 8 years of daily use. The door now slams, and each slam wears the hinge cup faster than normal.
- Snapped hinge ears or missing screws. Overtightening is the usual culprit. The steel ears break off, and then the entire hinge has to be replaced, usually in pairs so the door hangs even.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For part-specific repairs on IKO kitchen remodeling in Orlando, most hinges, slides, and dampers run $25 to $80 per part, and we typically replace hardware in pairs or sets so everything works evenly. Labor for a service call that involves swapping hinges on three to five doors starts around $180 to $350, depending on how many doors need realignment.
| Project | Orlando Price Range |
|---|---|
| Complete kitchen remodel | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What drives the range on a full IKO kitchen remodel is cabinet count, countertop square footage, and whether plumbing or electrical moves are involved. A straight cabinet-and-counter swap in a 10-by-10 Orlando kitchen lands at the lower end. Moving a sink, adding an island, or rewiring for under-cabinet lighting pushes it higher. Every price we give is written, line-itemed, and locked before any work starts. There are no change orders unless you change the scope, and we tell you that in writing too. The work is covered for 365 days from the completion date; if something isn’t right, we make it right at no cost to you.
DIY or Call Us?
Here’s the honest split. If a hinge has simply loosened, you can tighten it with a Phillips screwdriver. If a drawer slide has come unclipped, you can often snap it back into place. Those are safe, simple checks any Orlando homeowner can do in five minutes. Where DIY goes wrong is when the hinge is bent, the slide is worn internally, or the cabinet box has swollen. Then you’re guessing at part numbers, forcing screws into stripped holes, and spending three weekends on a fix that takes us one visit. There’s no dangerous tension or electrical risk with this particular work, but there is a fit-and-finish risk: a door that hangs 1/8-inch off marks the whole kitchen. Call us at (850) 920-7745 and tell me what the problem is. We’ll figure out the rest from there.
FAQs
Most hinges and slides last 8 to 12 years in normal Orlando residential use, but humidity shortens that for MDF cabinet boxes and the hardware mounted to them. If your kitchen is older than a decade and multiple doors are failing, replacement is the better investment than repeated part swaps.
Sometimes a loose hinge plate can be resecured with a larger-diameter screw, and a bent hinge arm can be straightened once, but it will re-bend. A worn slide is not repairable; the bearing race is physically destroyed. We’ll tell you which situation you have before recommending any parts. Call (850) 920-7745 for an exact assessment, and remember that estimate is free.
A typical service call replacing hinges, slides, or dampers on five to ten doors and drawers takes 2 to 3 hours on site. We bring the common parts on the truck; anything outside our stock takes 5 to 7 business days to source.
We stock the most common hinge cup sizes, drawer slide lengths, and soft-close dampers on the truck, and we can order OEM IKO-compatible pieces when the original part is identifiable. If your part isn’t something we carry, we’ll give you a written quote for the ordered part before you pay a dime.
When you’re ready to stop fighting a drawer that sticks or a door that won’t close, call (850) 920-7745. We’ll confirm what your IKO kitchen needs, put the price in writing, and send a crew member whose name and photo you’ll see before they arrive. That’s the way it should work, and it’s the way we’ve done it in Orlando for years.
Written by Isaac Pruett, Owner, Mason Remodeling Co Orlando at Mason Remodeling Co Orlando, serving Orlando and nearby areas.
