Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Kitchen Remodeling: The Orlando Owner’s Guide
KraftMaid kitchen remodeling in Orlando typically runs $14,000 to $45,000, with cabinet installation alone landing between $4,000 and $13,000. We stock KraftMaid-compatible cabinet parts, hinges, drawer slides, and replacement door fronts, and in most cases we can match your existing finish and install the same week. Homeowners usually discover they need us when a drawer starts grinding, a hinge lets a door sag, or a cabinet box shows water damage under the sink after years of Florida humidity.
What starts as one sticking drawer or a soft-close hinge that stopped catching often means the cabinet was installed before Orlando’s humidity was fully accounted for. KraftMaid cabinets are built in Ohio, and while the construction is solid, the thermofoil and wood veneers respond to our wet summers and dry winters in ways that older installs didn’t anticipate. The good news is that most failures are isolated and repairable without tearing out the whole kitchen.
Key takeaways:
- Most KraftMaid part failures in Orlando are hinge, slide, or finish issues, not structural cabinet failure.
- Replacement parts are matched by measurement and door profile, not just by series name.
- You’ll get a written price before any work starts, and a 365-day guarantee after it’s done.
Which KraftMaid Models This Applies To
KraftMaid builds across several lines, and parts compatibility depends more on the cabinet’s construction era than the marketing name. The Venicia line, for example, uses a different hinge mounting pattern than the more common raised-panel lines sold through big-box stores in Orlando. If your cabinets came from a builder supply house in the 2000s, you’re likely looking at standard 35mm cup hinges with a 1/2″ overlay. If they came from a specialty dealer, the overlay might be 1-1/4″ full overlay, which changes which hinge we order.
Here’s the compatibility gotcha most Orlando owners run into: KraftMaid changed their hinge supplier around 2012. Older cabinets used a square-corner mounting plate; newer ones use a round-corner plate. They are not interchangeable. When we arrive, we measure the cup diameter, the overlay, and the screw spacing, and we pull the original hinge to check for a stamped part number. That tells us whether to order OEM or whether a quality aftermarket equivalent like Salice or Blum will fit without modifying the door.
The finish matters too. KraftMaid’s “Honey Spice” maple from 2008 is not the same color as “Honey Spice” from 2016. The stain formula shifted when KraftMaid moved production. If you need a replacement door front or drawer face, we order from a finish-matched sample, not from the name on your original order sheet. It’s the only way to avoid a two-tone patch job.
Styles & brands we work with
Signs Your KraftMaid Kitchen Remodeling Is Failing
- Drawer slides that catch or grind. The ball bearings inside the slide have worn flat, or the nylon roller cracked under repeated load. Orlando’s humidity can accelerate rust on older steel slides, especially in base cabinets near the dishwasher.
- A door that sags and won’t close flush. The hinge has stretched or a screw has stripped out of the particleboard side panel. Left alone, the door will start rubbing the frame and wearing the finish off the corner.
- Soft-close dampers that stopped working. The small piston inside the hinge loses its fluid seal after years of use, or the plastic clip snapped. This is a part we replace on nearly every Orlando service call where cabinets are more than eight years old.
- Swollen or darkened cabinet floors under the sink. This is water damage, not a KraftMaid defect. A slow P-trap leak or a supply line drip has been soaking the particleboard for months. The cabinet box is compromised, and in Florida’s climate it will start growing mold if not addressed.
- Thermofoil peeling at the edges. KraftMaid’s thermofoil doors delaminate when heat and moisture work their way under the vinyl skin. We see it most on dishwasher-adjacent panels and on cabinets near the range. It’s a cosmetic failure that can’t be re-glued; the door front gets replaced.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full KraftMaid kitchen remodel in Orlando typically falls between $14,000 and $45,000 depending on kitchen size, cabinet count, countertop material, and whether we’re moving plumbing or electrical. If you’re only replacing cabinet parts rather than remodeling, the job is much smaller. Here’s what Orlando homeowners can expect:
- Cabinet installation (new KraftMaid boxes): $4,000 – $13,000
- Cabinet part replacement (hinges, slides, drawer fronts): $75 – $800 depending on part count and whether we’re ordering OEM
- Countertop installation (Cambria, Silestone): $2,000 – $6,500
- Backsplash installation: $800 – $2,500
- Kitchen island installation: $3,000 – $10,000
Every quote includes the parts, the labor, any hardware, and cleanup at the end of each day. We give you a written price before the first tool comes off the truck, and that price doesn’t change unless you change the scope. The work is covered for 365 days from the completion date. If a hinge fails or a drawer sticks within that year, we come back and fix it at no charge. That’s the guarantee, stated plainly.
DIY or Call Us?
For a stripped hinge screw or a loose drawer front, a homeowner with a drill and some wood glue can handle it in an afternoon. We’re not going to tell you otherwise. The key is matching the replacement hinge correctly. If you buy the wrong overlay or the wrong cup size, the door will sit crooked and you’ll have drilled new holes for nothing. That’s where we see Orlando DIY jobs go sideways most often.
The honest line is this: if it involves drilling into the cabinet box, matching a finish, or anything electrical like under-cabinet lighting, call us. Cabinet hinges and slides are low-risk. A sagging cabinet box that’s pulling off the wall is a structural problem that needs a professional eye and proper anchoring. Isaac Pruett will tell you straight if a job is worth your time or worth our crew. Tell me what the problem is. We’ll figure out the rest from there. Call (850) 920-7745 and we’ll walk through it on the phone before anyone schedules a visit.
FAQs
KraftMaid cabinet boxes typically last 20 to 30 years in Orlando if the home’s humidity is controlled and the cabinets stay dry. The finish on doors and drawer fronts usually shows wear first, often around years 12 to 15, while hinges and slides are consumables that get replaced every 8 to 12 years. The Florida factor is moisture: cabinets in homes without a whole-house dehumidifier age faster, especially in lower cabinets near plumbing. Call (850) 920-7745 and we’ll assess whether your cabinets have life left in them or whether replacement makes better financial sense.
Hinges, slides, drawer fronts, and door panels can almost always be repaired or replaced individually, which is far cheaper than gutting the kitchen. A structurally sound cabinet box with a water-damaged floor can sometimes be reinforced with a new base panel. But if the particleboard sides are swollen and crumbling, the box has lost its structural integrity and repair is throwing money at a lost cause. We’ll give you the straight answer after we look at it, with a written price either way.
Most hinge, slide, and drawer front replacements take one to two hours on site once we have the correct part in hand. If we need to order a finish-matched door front from KraftMaid, that typically adds two to three weeks for production and delivery. A full kitchen remodel usually runs four to eight weeks depending on scope, permit requirements, and countertop fabrication time.
We stock the most common KraftMaid hinge sizes, mounting plates, soft-close dampers, and drawer slide lengths on our service vehicles, so many Orlando repair calls are completed the same day. If your cabinet predates the 2012 hinge change, we may need to order a specific part to match. We also keep Cambria and Silestone samples, along with Kohler fixture catalogs, so you can see your options during the same visit.
Written by Isaac Pruett, Owner, Mason Remodeling Co Orlando at Mason Remodeling Co Orlando, serving Orlando and nearby areas.
