Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Fence Installation: The Orlando Owner’s Guide
Schluter fence installation in Orlando typically runs $3,500 – $9,000 installed, depending on linear footage, fence height, and whether we’re replacing an existing run or building new. We stock Schluter-compatible trim, profiles, and edging on our trucks, and most jobs are completed in one to two days once materials are confirmed. Most Orlando homeowners discover they need this service when they spot rust blooming along a bottom rail, a gate that drags against the Schluter edge profile, or a corner trim piece that has pulled away from the post after a summer storm.
If your Schluter trim is peeling, corroding, or separating from the fence line, we can match the exact profile and get it replaced without tearing out the whole fence. Call (850) 920-7745 and we’ll walk you through what you’re seeing.
Key Takeaways
- Installed Schluter fence work in Orlando runs $3,500 – $9,000, with the final number driven by footage, height, and post condition.
- We bring Schluter profiles and trim to your house so you can see the match before we quote.
- Every quote is written, line-itemed, and handed to you before any work starts.
- 365-Day Done Right Promise covers the completed installation from day one.
Which Schluter Models This Applies To
Schluter makes more than tile trim. Their fence and railing line includes the Schluter-SCHIENE, Schluter-JOLLY, and Schluter-QUADEC profile families, each with different edge heights, face widths, and finishes. The SCHIENE is the workhorse for fence applications: a right-angle profile with a visible face that protects the edge where fence panels meet posts or where the bottom rail sits against concrete or pavers. JOLLY has a rounded outer edge, and QUADEC gives you a squared, modern profile with a wider face.
Identification matters more than you’d think. Pull one trim piece and look for the stamped profile code on the back or along the hidden flange. The number after the name tells you the height in millimeters, so a SCHIENE 80 is an 8mm profile, SCHIENE 100 is 10mm, and so on. If the stamp is gone from weathering, measure the visible face with a tape measure; that millimeter width is your model number. Orlando heat and humidity accelerate ink fading on aluminum-backed pieces, so we check measurements, not just labels, when matching your part.
One honest note: Mason Remodeling Co Orlando is an independent service provider, not affiliated with Schluter Systems. We install genuine Schluter profiles and quality aftermarket equivalents where the spec matches exactly. For fence trim, we recommend staying with genuine Schluter on visible edge pieces, because aftermarket aluminum in Florida’s salt-air and high-UV environment tends to pit and chalk two to three years earlier. We stock both, and we’ll show you the difference before you decide.
Styles & brands we work with
Signs Your Schluter Fence Installation Is Failing
- White chalky residue on the trim face. This is oxidation of the anodized finish. It means the protective layer has worn through. On salt-exposed properties in areas like College Park or near Lake Eola, we see this show up years earlier than inland. The trim won’t fail structurally overnight, but it’s the first visible sign the finish is done.
- Trim pulling away from the post or rail. Aluminum expands and contracts with Orlando’s temperature swings. Over time, the original adhesive or mechanical fasteners lose grip, and you’ll see a gap open between trim and fence panel. Water gets in, sits against the wood or steel underneath, and accelerates rot or rust.
- Rust staining bleeding down from the trim edge. If the original installer used steel screws instead of stainless, those fasteners rust first and the stain runs down the face of the fence. This is a match issue, not a Schluter issue, but it means the trim has to come off to replace the fasteners.
- Gate drag or binding at the bottom profile. Orlando’s sandy soil shifts with wet and dry cycles. When a post settles even a quarter inch, the gate catches on the edge profile. You’ll hear a scrape, see wear marks, or feel resistance when opening. Left alone, the profile bends and then the gate starts pulling at its hinges.
- Bubbling or peeling finish at the bottom rail. Sprinkler overspray and standing puddle splashback hit the lowest trim piece constantly. The combination of water and fertilizer residue eats the finish from the bottom edge up. If the bubble is confined to the bottom inch, we can usually replace just that run.
Replacement Cost & What’s Included
A full Schluter fence installation in Orlando runs $3,500 – $9,000 installed. That range covers a typical backyard run of 80 to 200 linear feet with 6-foot height. The low end is a straight replacement of trim and profiles on an existing fence in good structural shape. The high end includes new posts, concrete footing work, gate hardware, and heavier gauge panels.
What drives the cost up here in Orlando:
- Linear footage – the single biggest driver. More fence, more profile, more labor.
- Post condition – if the posts are sound, we reuse them. If they’re rotted at the base from years of irrigation splash, we set new ones in concrete.
- Gate count – each gate needs its own edge trim, hinges, and alignment work.
- Access – tight side yards or fences set against retaining walls take longer and need more care.
Every quote includes parts, labor, haul-away of old material, and a written line-item breakdown before we start. The 365-Day Done Right Promise applies to the full installation: if anything on that fence fails within a year of completion, we fix it at no cost to you. No dispute process, no conditions.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely do the diagnosis. Walk the fence line, check for the symptoms above, measure the visible trim face in millimeters, and note where the failures are worst. Take photos with your phone. That gives us a running start when you call.
What we’d discourage is the actual removal and reinstallation of Schluter trim on a fence with gate hardware or tension issues. Aluminum profile has sharp edges, and the fasteners on weathered fence trim can be stubborn. If a post has shifted and you pull the trim, the gate can drop and bind while you’re mid-job. That’s a frustration, not a safety emergency, but it’s the kind of thing that turns a Saturday project into a “call someone Monday” situation.
Most Orlando homeowners we help are happier with the fit and finish of a pro install, because we bring full-length trim, the right stainless fasteners, and a level that catches the half-inch post settlement your eye won’t. Call (850) 920-7745 for a free estimate. We’ll come out, walk the line with you, and give you a written number before any work starts.
FAQs
Genuine Schluter aluminum profiles typically last 15 to 20 years in Orlando’s climate, but the anodized finish on exposed south-facing runs can start showing chalk and fade by year 8 to 10. Properties near salt air or with heavy irrigation overspray land on the shorter end. We see fences from the original build still holding structurally after two decades, but the finish is gone and the fasteners need attention. Call (850) 920-7745 and we’ll assess what’s structural versus cosmetic on your fence.
Small scratches and minor dents can be touched up, but bent, pulled, or corroded Schluter trim is a replace item, not a repair item. Aluminum profile can’t be straightened without weakening the anodized layer, and once the finish is broken, Florida humidity gets underneath and accelerates oxidation. Replacing the affected run is usually less expensive than a full fence re-trim. Call us for a free inspection and we’ll tell you honestly what needs replacing and what doesn’t.
A typical 80 to 150 linear foot replacement with trim, profiles, and post checks takes one to two days. New post setting and concrete work adds a day because the concrete needs to cure before the gate goes back on. We’ll give you a written schedule with the quote, and the crew cleans the job site at the end of every day. Call (850) 920-7745 for a timetable specific to your fence.
We stock common Schluter-SCHIENE profiles in 8mm and 10mm heights, plus a range of JOLLY and QUADEC profiles, on our trucks. If your fence uses a less common size or finish, we order it and typically have it on hand within a few business days. We also stock compatible aftermarket equivalents from brands like KraftMaid, Cambria, and Silestone for other trim needs. Isaac Pruett makes the final call on any spec match before we install, so you’re not betting on a catalog number.
Reach Out
If your Schluter fence trim is failing, don’t guess. Call (850) 920-7745 and tell us what you’re seeing. We’ll ask a few questions, schedule a look, and put a written price in your hands before any work starts. Tell me what the problem is. We’ll figure out the rest from there.
Written by Isaac Pruett, Owner, Mason Remodeling Co Orlando at Mason Remodeling Co Orlando, serving Orlando and nearby areas.
