Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tremron Bathroom Remodeling: The Orlando Owner’s Guide
If your Tremron bathroom fixture or component has failed, you’re in the right place. We stock and install Tremron-compatible bathroom remodeling components across Orlando, with most full bathroom remodels running $9,000 to $28,000 installed. Smaller parts swaps, like a shower valve or drain assembly, often come in well under that. Homeowners usually call us after a slow leak turns into a ceiling stain downstairs, or when water pressure drops and won’t come back no matter how many times they clean the showerhead.
We’re an independent Orlando contractor, not affiliated with Tremron, but we’ve worked on enough of their products to know the quirks. Orlando’s hard water, which runs heavy with calcium and mineral deposits from the Floridan aquifer, attacks seals, cartridges, and valve bodies faster than the national average. That’s the single biggest reason Tremron fixtures fail here: mineral buildup, not manufacturing defects.
If you’re reading this because water is where it shouldn’t be, shut off the fixture’s supply line or the bathroom’s dedicated shutoff valve. Then call us. Tell me what the problem is. We’ll figure out the rest from there.
Which Tremron Models This Applies To
Tremron has produced several bathroom fixture lines over the years, and compatibility is not universal. The main series you’ll see in Orlando homes are the Tremron Classic, Tremron Estate, and Tremron Proline collections. Each uses different valve cartridges, stem extensions, and trim kits. A shower cartridge from a Tremron Estate faucet will not seat properly in a Proline valve body, even if they look close at a glance.
Before you order anything, identify the model. Look under the sink basin or on the escutcheon plate for an engraved model number. On shower systems, the number is typically stamped on the valve body behind the trim plate. Take a photo with your phone and compare it against the spec sheet. If you can’t find it, remove the handle and measure the cartridge stem in millimeters. Classic series stems run 12mm, Estate runs 14mm, Proline runs 16mm. Getting this measurement wrong means a second trip to the supply house and more water shut off for no reason.
When it comes to OEM versus aftermarket, our honest position on Tremron is this: OEM cartridges and trim kits are worth the premium for anything that moves or seals. Aftermarket drain assemblies and escutcheon plates are usually fine. The failure points that make homeowners regret a cheap part are almost always the cartridge and the pressure-balancing unit, so we don’t cut corners there.
Styles & brands we work with
Signs Your Tremron Bathroom Remodeling Is Failing
- Water pressure drops in one fixture only. Sediment or mineral scale is blocking the Tremron cartridge inlet ports. In Orlando, this typically happens within 5 to 7 years of installation because our water supply is so mineral-heavy.
- A drip that won’t stop, even with the handle tight. The ceramic disc inside the cartridge is worn or cracked. Tightening the handle harder just scores the stem and makes the eventual repair more expensive.
- Temperature changes when someone flushes a toilet. The pressure-balancing spool inside the valve has seized from scale. That’s a Tremron-specific part, and it fails more often in Florida than anywhere else we’ve seen because of humidity plus hard water.
- Water stains on the ceiling below a second-floor bath. The drain flange gasket or the supply line connection has failed. This is the call you make same-day before a small fix becomes drywall and paint work.
- Grout in the shower floor stays dark after it dries. Water is migrating through failed grout or a cracked shower pan. Tremron pans, like most, develop hairline fractures along the drain collar over time. We see this constantly in Orlando’s older tract homes built in the 1980s and 1990s.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full Tremron bathroom remodel in Orlando ranges from $9,000 to $28,000 installed. A guest bath on the smaller side with a tub-to-shower conversion and a new Tremron-compatible valve typically lands between $9,000 and $14,000. A primary bath with a walk-in shower, custom tile, a new vanity, and upgraded fixtures moves toward the upper end. If you’re only replacing a failed part, a Tremron cartridge swap runs $180 to $400 installed, and a full valve body replacement runs $600 to $1,500 depending on wall access.
| Service | Orlando Installed Price |
|---|---|
| Tremron cartridge replacement | $180 – $400 |
| Tremron valve body replacement | $600 – $1,500 |
| Tub-to-shower conversion with Tremron fixtures | $3,500 – $10,000 |
| Full Tremron-compatible bathroom remodel | $9,000 – $28,000 |
Every quote we give in Orlando is a written price before any work starts. That includes the parts, labor, and haul-away of the old fixtures. If we find something unexpected inside the wall, we stop and talk to you before spending another dollar. Our work is covered by the 365-Day Done Right Promise: if it’s not right within a year of completion, we make it right at no cost to you. Parts carry their manufacturer warranty in addition to our workmanship guarantee.
DIY or Call Us?
There is a safe DIY lane here, and then there is a lane that can flood your house. Replacing a showerhead, a drain cover, or an escutcheon plate is straightforward and low-risk. Shut off the water, go slow, use plumber’s tape on threaded connections. Replacing a shower cartridge crosses into plumbing work: you are working inside the wall, near supply lines under pressure, and one wrong turn on a seized stem can snap the valve body and require opening the wall. That is not a Saturday project that ends well without experience and the right tools.
If the part you’re replacing carries water pressure, call us. If you’ve already shut off the water and you’re looking at a part that won’t budge, stop before it gets worse. We show up with the right Tremron parts on the truck and do the swap in a single visit, most of the time. Call (850) 920-7745 and we’ll walk you through what you’re seeing before we even schedule anything.
Frequently Asked Questions
In Orlando’s hard water and humidity, Tremron cartridges and pressure-balancing units typically last 5 to 8 years before mineral buildup causes failure. The trim and handles usually outlast the internal components because they aren’t constantly exposed to water flow. If you’re at the 7-year mark and noticing pressure or temperature issues, the cartridge is almost certainly near the end of its useful life. Call (850) 920-7745 and we’ll confirm what you need.
Sometimes yes. If the failure is a clogged aerator or a loose retaining nut, that’s a repair, not a replacement. But worn cartridges, cracked ceramic discs, and seized pressure-balancing spools are not repairable, they’re replaceable. Trying to repair them usually extends the problem, not the life of the part. We’ll tell you straight which situation you have when we look at it.
Most cartridge or valve component swaps take 1 to 2 hours once we’re on site. A tub-to-shower conversion runs 2 to 3 days. A full bathroom remodel runs 1 to 3 weeks depending on tile work, plumbing reroutes, and whether we’re moving walls.
We carry the most common Tremron cartridges, pressure-balancing units, and trim kits for the Classic, Estate, and Proline series on our Orlando service trucks. If your part is unusual or discontinued, we source it same-day or next-day through our supply partners, including KraftMaid, Cambria, and Silestone for surrounding finish work. Call (850) 920-7745 and we’ll verify availability before you schedule.
Written by Isaac Pruett, Owner, Mason Remodeling Co Orlando at Mason Remodeling Co Orlando, serving Orlando and nearby areas.
